1/25/2024 0 Comments Clear 3m tape![]() On the CF piece I did a little Goo Gone to get rid of residue from original tape, then wiped with alcohol and scuffed very lightly with a little sandpaper. Good luck.įor the prep of the bumper I had cleaned with dawn and used the alcohol. So in my opinion the 3M tape should be enough to do the job. I think because the fitment is so tight and the splitters aren't at all flexible they are much harder to fit. I've also washed the car and driven for a while over 110kph (65mph) and had heat around 30 degrees celcius (around 100 degrees F I think) without any change. I did this a few weeks ago now and only one side has slid down a tiny amount that isn't obvious enough to worry about. ![]() Was a pain (literally) to do and I'd recommend getting another pair of hands to assist but it finally worked. So on my third attempt I made sure I very firmly pressed the splitter onto the bumper where it should go and then continued to press firmly to hold it in place while tightening the four screws up underneath. So even though my car was only two days old and spotless I cleaned that area and dried it off and reinstalled the splitters using 3M tape exclusively after removing the supplied tape. I contacted Exotic and got a swift response from Ken who mentioned cleaning the bumper to remove any wax/polish etc to ensure a good surface to cling to. Turns out that a combo of both wouldn't hold either. On my first install I had some 3M double sided tape lying around and used some as I wasn't convinced that the supplied tape would hold. I had the same problem as you with the splitters sliding down after installation within a couple of hours of the car just sitting in the garage. However, I don't know what this is, how reversible, how easy to use, or what other options are. I read something about 'betalink' or (something like that) that people were using to more securely hold down corners of rear carbon fiber spoilers that were not a perfect fit and wanted to pull up. Simply driving the car no more than 40mph is not an option. What next? I want something that is reversible and won't hurt the paint, but will hold better as the hot weather approaches. Unfortunately, after sitting in the sun in a parking lot for about an hour and driving 80 on the way home on the interstate, they moved again and did not look as good again. I took off all the tape, cleaned the surface on the inside of the splitter well, and put on a double size dose of the 3M mounting tape. ![]() At first, I took them off and found that they are actually separating on the splitter side vs the side that attaches to the lower bumper. they are well connected to the bottom via the 4 screws on each side that attach the bumper to the liner underneath. The heat seems to soften the adhesive on the tape, and when combined with the downforce, it wants to slide down a little and then does not look quite right after. This is especially true as the weather warms and at highway (or slightly higher ) speeds. ![]() 1 solid one all the way e sample picture below) from Exotics Tuning that I really like, but the adhesive tape is just not up to the task. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.I've got some Carbon Fiber front splitters (one on each side vs. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. Not for consumer sale or use.ģM industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |